LEAD(II) SULFATE Property

Melting point:

1170 °C

Density 

6.2 g/mL at 25 °C(lit.)

solubility 

insoluble in acid solutions; slightly soluble in alkaline solutions

form 

Powder/Lump

Specific Gravity

6.2

color 

White

Water Solubility 

Partially soluble in water, dilute HCl and HNO{3}. Soluble in sodium hydroxide, ammonium acetate or tartrate, concentrated hydriodic acid. Insoluble in alcohol

Merck 

14,5420

Exposure limits

ACGIH: TWA 0.05 mg/m3
NIOSH: IDLH 100 mg/m3; TWA 0.050 mg/m3

Dielectric constant

14.3（0.0℃）

Stability:

Stable.

CAS DataBase Reference

7446-14-2(CAS DataBase Reference)

EPA Substance Registry System

Lead(II) sulfate (7446-14-2)

Safety

Hazard Codes 

T,N

Risk Statements 

61-20/22-33-50/53-62

Safety Statements 

53-45-60-61

RIDADR 

UN 3077 9/PG 3

WGK Germany 

3

RTECS 

OG4375000

TSCA 

Yes

HazardClass 

6.1

PackingGroup 

III

HS Code 

28332960

Hazardous Substances Data

7446-14-2(Hazardous Substances Data)

Hazard and Precautionary Statements (GHS)

Symbol(GHS)

Signal word

Danger

Hazard statements

H373May cause damage to organs through prolonged or repeated exposure

H410Very toxic to aquatic life with long lasting effects

Precautionary statements

P202Do not handle until all safety precautions have been read and understood.

P260Do not breathe dust/fume/gas/mist/vapours/spray.

P273Avoid release to the environment.

P301+P312IF SWALLOWED: call a POISON CENTER or doctor/physician IF you feel unwell.

P308+P313IF exposed or concerned: Get medical advice/attention.

LEAD(II) SULFATE Chemical Properties,Usage,Production

Physical Properties

White monoclinic or rhombic crystals; refractive index 1.877; density 6.20 g/cm3; melts at 1,170°C; very slightly soluble in water, 42.5 mg/L at 25°C; KSP1.82x10–8; sparingly soluble in hydrochloric and nitric acids; slightly soluble in dilute sulfuric acid, more soluble in concentrated sulfuric acid; insoluble in alcohol; soluble in caustic soda and ammonium salts solutions.

Occurrence and Uses

Lead sulfate occurs in nature as the mineral, anglesite. It is an essential component of lead-sulfuric acid storage batteries and forms during discharge cycles. It is used as an additive to stabilize clay soil for construction. Other applications are in photography and as a pigment.

Preparation

Lead sulfate precipitates when an aqueous solution of lead nitrate or other soluble salt of lead is treated with sulfuric acid.
Alternatively, lead sulfate may be prepared by treating lead oxide, hydroxide, or carbonate with concentrated sulfuric acid under warm condition. It also is produced when lead sulfide is roasted in air.

Toxicity

Low to moderate toxicity by ingestion. Irritant action on eye, skin, and mucous membranes.

Description

Lead sulfate is a heavy, white crystallinepowder. Molecular weight=303.25; Freezing/Meltingpoint = 1170℃. Hazard Identification (based on NFPA-704M Rating System): Health 3, Flammability 0, Reactivity 1.Soluble in water.

Chemical Properties

white crystals or powder

Chemical Properties

Lead sulfate is a heavy, white crystalline powder.

Uses

It has been used in photography in combination with silver bromide and is used in the stabilization of clay soil for adobe structures, earth-fill dams, and roads.

Uses

Lead(II) sulfate is used in pigments, galvanic batteries, lithography, weighting fabrics. It is also used as intermediates.

Uses

As pigment instead of white lead; manufacture of galvanic and lead-acid batteries; manufacture of minium, in lithography; preparing rapidly drying oil varnishes; weighting fabrics.

Definition

anglesite: A mineral form oflead(II) sulphate, PbSO₄.

Production Methods

Lead sulfate, PbSO4, is soluble in concentrated acids and alkalies, forming hydroxyplumbites. It is prepared by treating lead oxide, hydroxide, or carbonate with warm sulfuric acid, or by treating a soluble lead salt with sulfuric acid.

General Description

A white crystalline solid. Insoluble in water and sinks in water. Contact may irritate skin, eyes, and mucous membranes. May be mildly toxic by ingestion, inhalation and skin absorption. Used to make other chemicals. Use: in lithography, battery acid solution treated fabrics, used in varnishes.

Air & Water Reactions

Insoluble in water.

Reactivity Profile

LEAD(II) SULFATE reacts explosively with boric acid [Bretherick 1979. p. 1029]. Special Hazards of Combustion Products: Toxic metal fumes [USCG, 1999].

Health Hazard

INHALATION: Joint and muscle pains, headache, dizziness and insomnia. Weakness, frequently of extensor muscles of hand and wrist (unilateral or bilateral). Heavy contamination. Brain damage. Stupor progressing to coma - with or without convulsion, often death. Excitation, confusion, and mania less common. Cerebrospinal pressure may be increased. EYES: Caused a moderat purulent reaction and general inflammation of the rabbit eye. INGESTION: Abdominal pain, diarrhea, constipation, loss of appetite, muscular weakness, headache, blue line on gums, metallic taste, nausea and vomiting.

Fire Hazard

Special Hazards of Combustion Products: Toxic metal fumes

Potential Exposure

Lead sulfate is used in storage batteries and paint pigments. Used in the making of alloys, fastdrying oil varnishes; weighting fabrics; in lithography

First aid

If this chemical gets into the eyes, remove anycontact lenses at once and irrigate immediately for at least15 min, occasionally lifting upper and lower lids. Seek medical attention immediately. If this chemical contacts theskin, remove contaminated clothing and wash immediatelywith soap and water. Seek medical attention immediately. Ifthis chemical has been inhaled, remove from exposure,begin rescue breathing (using universal precautions, including resuscitation mask) if breathing has stopped and CPR ifheart action has stopped. Transfer promptly to a medicalfacility. When this chemical has been swallowed, get medical attention. Do not induce vomiting.Note to physician: whole blood lead levels, circulatingplasma/erythrocyte lead concentration ratio, urine ALA,and erythrocyte protoporphyrin fluorescent microscopy mayall be useful in monitoring or assessing lead exposure.Chelating agents, such as edetate disodium calcium (CaEDTA) and penicillamine (not penicillin), are generallyuseful in the therapy of acute lead intoxication.Antidotes and special procedures for lead: Persons with significant lead poisoning are sometimes treated with CaEDTA while hospitalized. This “chelating” drug causes arush of lead from the body organs into the blood and kidneys, and thus has its own hazards, and must be administered only by highly experienced medical personnel undercontrolled conditions and careful observation. Ca EDTA orsimilar drugs should never be used to prevent poisoningwhile exposure continues or without strict exposure control,as severe kidney damage can result.Note to physician: For severe poisoning BAL [British AntiLewisite, dimercaprol, dithiopropanol (C3H8OS2)] has beenused to treat toxic symptoms of certain heavy metals poisoning. In the case of lead poisoning it may have SOMEvalue. Although BAL is reported to have a large margin of safety, caution must be exercised, because toxic effects maybe caused by excessive dosage. Most can be prevented bypremedication with 1-ephedrine sulfate (CAS: 134-72-5).

storage

Color Code—White: Corrosive or Contact Hazard;Store separately in a corrosion-resistant location. Prior toworking with this chemical you should be trained on its proper handling and storage. Lead sulfate must be stored toavoid contact with oxidizers (such as perchlorates, peroxides, permanganates, chlorates, and nitrates) and chemicallyactive metals (such as potassium, sodium, magnesium, andzinc), since violent reactions occur. Lead is regulated by anOSHA Standard 1910.1025. All requirements of the standard must be followed. A regulated, marked area should beestablished where this chemical is handled, used, or storedin compliance with OSHA Standard 1910.1045.

Shipping

UN2291 Lead compounds, soluble n.o.s., Hazard Class: 6.1; Labels: 6.1-Poisonous materials, Technical Name Required. UN1794 Lead sulfate with more than 3% free acid, Hazard class: 8; Labels: 8-Corrosive material. UN3077 Environmentally hazardous substances, solid, n.o. s., Hazard class: 9; Labels: 9-Miscellaneous hazardous material, Technical Name Required

Incompatibilities

Incompatible with oxidizers (chlorates, nitrates, peroxides, permanganates, perchlorates, chlorine, bromine, fluorine, etc.); contact may cause fires or explosions. Contact with potassium can cause explosion. Keep away from alkaline materials, strong bases, strong acids, oxoacids, and epoxides