Aptazapine Chemical Properties

Boiling point:

432.6±45.0 °C(Predicted)

Density 

1.22±0.1 g/cm3(Predicted)

pka

8.44±0.20(Predicted)

Aptazapine Usage And Synthesis

Originator

Aptazapine maleate,ZYF Pharm Chemical

Uses

Antidepressant.

Manufacturing Process

To the suspension of 12.8 g of 2-methyl-3,4-dioxo-1,3,4,14b-tetrahydro-10Hpyrazino[ 1,2-a]pyrrolo[2,1-c][1,4]benzodiazepine in 460 ml of tetrahydrofuran, 200 ml of 1-molar diborane in tetrahydrofuran are added while stirring and cooling with ice. The mixture is refluxed for one hour, again cooled and combined with 25 ml of acetic acid. It is evaporated, the residue taken up in 50 ml of 30% aqueous sodium hydroxide and the mixture extracted with methylene chloride. The extract is dried, evaporated, the residue dissolved in diethyl ether, the solution filtered and the filtrate evaporated, to yield the crude 2-methyl-1,3,4,14b-tetrahydro-10Hpyrazino[ 1,2-a]pyrrolo[2,1-c][1,4]benzodiazepine. It is triturated with ethyl acetate-diethyl ether, chromatographed on 70 g of silica gel and eluted with methanol-chloroform (1:9). The eluate is evaporated and the residue salified.
9.7 g thereof are dissolved in the minimum amount of isopropanol and the solution acidified with a concentrated solution of 4.45 g of maleic acid is isopropanol. The precipitate formed is collected and recrystallized from methanol-diethyl ether, to yield the corresponding mono-maleate melting at 180°-182°C.
The starting material is prepared as follows: the mixture of 54.0 g of Npotassium phthalimide, 50.0 g of o-nitrobenzyl chloride and 120 ml of dimethylformamide is refluxed for 3 hours and poured into 900 ml of icewater while stirring. After 30 minutes, it is filtered, and the residue washed with water, to yield the N-o-nitrobenzyl-phthalimide melting at 190°-209°C.
The mixture of 70.0 g thereof, 14.6 g of hydrazine hydrate and 600 ml of ethanol is refluxed for 4 hours and combined with 50 ml of concentrated hydrochloric acid. After 30 minutes, it is cooled to room temperature, filtered and the residue washed with water. The filtrate is concentrated, the aqueous concentrate filtered and the filtrate basified with 3 N aqueous sodium hydroxide. It is extracted with diethyl ether, the extract dried and evaporated, to yield the o-nitrobenzylamine.
To the solution of 7.6 g thereof in 25 ml of glacial acetic acid, 6.6 g of 2,5- dimethoxytetrahydrofuran are added and the mixture is refluxed for one hour. It is evaporated, the residue poured into ice water and the mixture extracted with ethyl acetate. The extract is washed with saturated aqueous sodium bicarbonate, dried and evaporated. The residue is taken up in diethyl ether, the solution decolorized with charcoal, filtered and evaporated, to yield the 1- (o-nitrobenzyl)pyrrole.
Through the mixture of 13.42 g thereof, 140 ml of diethyl ether and 6.85 ml of chloroacetonitrile, hydrogen chloride is bubbled while stirring and cooling in an ice-salt bath. The saturated mixture is stirred at room temperature overnight, filtered and the residue suspended in 100 ml of water. It is extracted 3 times with 100 ml of ethyl acetate, warmed on the steam bath while stirring until all is dissolved, and the solution evaporated, to yield the 1- o-nitrobenzyl-2-chloroacetylpyrrole.
To the solution of 16.2 g thereof in 450 ml of ethanol, 14.10 g of N-methylbenzylamine are added and the mixture is refluxed for 3 hours. It is evaporated, the residue taken up in methylene chloride, the solution washed with saturated aqueous sodium carbonate dried, filtered and evaporated. The residue is triturated with diethyl ether, to yield the 1-(o-nitrobenzyl)-2-(Nmethyl- N-benzylaminoacetyl)pyrrole.
The solution of 3.0 g thereof in 30 ml of glacial acetic acid is hydrogenated over 100 mg of platinum oxide at 2.7 atm and room temperature until the theoretical amount of hydrogen has been absorbed. It is filtered, the filtrate evaporated, the residue taken up in methylene chloride-diethyl ether and the solution washed with saturated aqueous sodium bicarbonate. It is dried, evaporated, the residue chromatographed on 30 g of silica gel and eluted with methanol-chloroform (1:9), to yield the 11-(N-methyl-N-benzylaminomethyl)- 10,11-dihydro-5H-pyrrolo[2,1-c][1,4]benzodiazepine melting at 147°-149°C. The solution of 500 mg thereof in 35 ml of ethanol and 5 ml of glacial acetic acid is hydrogenated over 250 mg of 5% palladium on charcoal at 2.7 atm and 40°C for 7 hours. The mixture is filtered, the filtrate evaporated and the residue taken up in methylene chloride. The solution is washed with saturated aqueous sodium carbonate, the aqueous phase extracted with methylene chloride and the combined organic solutions dried and evaporated, to yield the 11-(N-methylaminomethyl)-10,11-dihydro-5H-pyrrolo[2,1- c][1,4]benzodiazepine.
The mixture of 300 mg thereof and 232 mg of diethyl oxalate is slowly heated to 140°C during 45 minutes and to 180°C during 15 minutes, at which temperature it is maintained for 30 minutes. It is cooled, diluted with benzene, chromatographed on silica gel and eluted with methanol-chloroform (1:9), to yield the 2-methyl-3,4-dioxo-1,3,4,14b-tetrahydro-10H-pyrazino[1,2- a]pyrrolo[2,1-c][1,4]benzodiazepine melting at 178°-179°C.
In practice it is usually used as maleate salt.

Therapeutic Function

Antidepressant

Aptazapine(71576-40-4)Related Product Information

• Mirtazapine
• Aptazapine
• 10,11-DIHYDRO-5H-BENZO[E]PYRROLO[1,2-A][1,4]DIAZEPINE
• (2-(PIPERAZIN-1-YL)PHENYL)METHANAMINE
• Serazapine
• 2-methyl-1-phenylpiperazine
• 1-[2-(4-Methylpiperazin-1-yl)phenyl]methanamine