Basic information Safety Supplier Related

Boronic acid, (4-cyano-3-methoxyphenyl)- (9CI)

Basic information Safety Supplier Related

Boronic acid, (4-cyano-3-methoxyphenyl)- (9CI) Basic information

Product Name:
Boronic acid, (4-cyano-3-methoxyphenyl)- (9CI)
Synonyms:
  • Boronic acid, (4-cyano-3-methoxyphenyl)- (9CI)
  • 4-Cyano-3-Methoxyphenylboronic Acid(WX650131)
  • 4-Cyano-3-methoxyphenylboronic acid 97%
  • Boronic acid, B-(4-cyano-3-methoxyphenyl)-
  • (4-Cyano-3-methoxyphenyl)boronic acid (contains varying amounts of Anhydride)
  • 4-Cyano-3-methoxybenzene boronic acid
CAS:
677777-45-6
MF:
C8H8BNO3
MW:
176.96
Product Categories:
  • METHOXY
Mol File:
677777-45-6.mol
More
Less

Boronic acid, (4-cyano-3-methoxyphenyl)- (9CI) Chemical Properties

Boiling point:
417.6±55.0 °C(Predicted)
Density 
1.26±0.1 g/cm3(Predicted)
storage temp. 
under inert gas (nitrogen or Argon) at 2-8°C
pka
6.90±0.10(Predicted)
form 
solid
color 
White to off-white
More
Less

Safety Information

RIDADR 
3439
HazardClass 
6.1
PackingGroup 
HS Code 
2931900090
More
Less

Boronic acid, (4-cyano-3-methoxyphenyl)- (9CI) Usage And Synthesis

Synthesis

330793-38-9

677777-45-6

The general procedure for the synthesis of (4-cyano-3-methoxyphenyl)boronic acid from 2-methoxy-4-bromobenzonitrile was as follows: an overhead mechanical stirrer and a nitrogen inlet tube were assembled in a 1L three-necked round-bottomed flask. To the reaction flask was added 45.56 g (215 mmol) of 4-bromo-2-methoxybenzonitrile, 64 mL (277 mmol) of triisopropyl borate, and 500 mL of anhydrous THF.The reaction system was cooled to -78 °C in a dry ice/acetone bath. A n-butyllithium solution (2.5 M in hexane, 110 mL, 275 mmol) was slowly added dropwise through a constant pressure dropping funnel. After dropwise addition, the reaction was maintained at -78 °C with continued stirring for 30 min, followed by addition of 2N hydrochloric acid solution to quench the reaction. The reaction mixture was stirred at room temperature for 1 h and then poured into ice water. The aqueous phase was extracted three times with ether (Et2O). The organic phases were combined and back-extracted with 1N sodium hydroxide solution. The alkaline aqueous phase was washed with ether and acidified with concentrated hydrochloric acid to pH < 2. The acidified aqueous phase was again extracted with ether. The organic phases were combined, dried with anhydrous magnesium sulfate, filtered and concentrated under reduced pressure to give 20.77 g (55% yield) of the target product (4-cyano-3-methoxyphenyl)boronic acid as a white solid. The product was characterized by 1H NMR (500 MHz, d6-DMSO): δ 7.68 (d, J=8.0 Hz, 1H), 7.59 (s, 1H), 7.47 (d, J=8.0 Hz, 1H), 3.95 (s, 3H).

References

[1] Patent: WO2005/95400, 2005, A1. Location in patent: Page/Page column 341

Boronic acid, (4-cyano-3-methoxyphenyl)- (9CI)Supplier

BeiJing Hwrk Chemicals Limted
Tel
0757-86329057 18934348241
Email
sales4.gd@hwrkchemical.com
Energy Chemical
Tel
021-021-58432009 400-005-6266
Email
sales8178@energy-chemical.com
Shanghai Topbiochem Technology Co., Ltd
Tel
021-58170097
Email
info@topbiochem.com
Jiangsu Aikon Biopharmaceutical R&D co.,Ltd.
Tel
025-66113011 17798518460
Email
cfzhang@aikonchem.com
9ding chemical ( Shanghai) Limited
Tel
4009209199
Email
sales@9dingchem.com