Product Identification

Product Name

N-((4-Aminophenyl)sulfonyl)acetamide

Synonyms

Acetosulfamin
N-[(4-Aminophenyl)sulfonyl]acetamide
N-Acetylsulfanilamide
p-Aminobenzenesulfonacetamide
Sulfacetamide
Urosulfon

CAS

144-80-9

Formula

C8H10N2O3S

Molecular Weight

214.25

EINECS

205-640-6

RTECS

AC8450000

RTECS Class

Mutagen; Reproductive Effector

Merck

12,9067

Beilstein/Gmelin

981718

Beilstein Reference

4-14-00-02662

Physical and Chemical Properties

Appearance

White powder.

Solubility in water

Insoluble

Melting Point

172 - 174

Boiling Point

475

Vapor Pressure

3E-9 (25 C)

Density

1.37 g/cm3

pKa/pKb

10.07 (pKb)

Partition Coefficient

3.05

Heat Of Vaporization

73.9 kJ/mol

Usage

A sulfonamide antibiotic. It may also have anti-inflammatory properties .

Refractive Index

1.5611 (176 C)

First Aid Measures

Ingestion

DO NOT INDUCE VOMITING. If the victim is conscious and not convulsing, give 1 or 2 glasses of water to dilute the chemical and IMMEDIATELY call a hospital or poison control center. Be prepared to transport the victim to a hospital if advised by a physician.

Inhalation

IMMEDIATELY leave the contaminated area; take deep breaths of fresh air. If symptoms (such as wheezing, coughing, shortness of breath, or burning in the mouth, throat, or chest) develop, call a physician and be prepared to transport the victim to a hospital. Provide proper respiratory protection to rescuers entering an unknown atmosphere. Whenever possible, Self-Contained Breathing Apparatus (SCBA) should be used.

Skin

IMMEDIATELY flood affected skin with water while removing and isolating all contaminated clothing. Gently wash all affected skin areas thoroughly with soap and water. If symptoms such as redness or irritation develop, IMMEDIATELY call a physician and be prepared to transport the victim to a hospital for treatment.

Eyes

First check the victim for contact lenses and remove if present. Flush victim's eyes with water or normal saline solution for 20 to 30 minutes while simultaneously calling a hospital or poison control center. Do not put any ointments, oils, or medication in the victim's eyes without specific instructions from a physician. IMMEDIATELY transport the victim after flushing eyes to a hospital even if no symptoms (such as redness or irritation) develop.

Handling and Storage

Storage

Keep in a cool, dry, dark location in a tightly sealed container or cylinder. Keep away from incompatible materials, ignition sources and untrained individuals. Secure and label area. Protect containers/cylinders from physical damage.

Handling

All chemicals should be considered hazardous. Avoid direct physical contact. Use appropriate, approved safety equipment. Untrained individuals should not handle this chemical or its container. Handling should occur in a chemical fume hood.

Exposure Controls/Personal Protection

Personal Protection

Chemical splash goggles in compliance with OSHA regulations are advised; however, OSHA regulations also permit other type safety glasses. Whre chemical resistant gloves. To prevent repeated or prolonged skin contact, wear impervious clothing and boots.

Respirators

Wear a NIOSH-approved half face respirator equipped with an organic vapor/acid gas cartridge (specific for organic vapors, HCl, acid gas and SO2) with a dust/mist filter.

Exposure Effects

The toxicological properties of this material have not been investigated.

Fire Fighting Measures

Flash Point

241

Fire Fighting

Fires involving this material can be controlled with a dry chemical, carbon dioxide or Halon extinguisher.

Fire Potential

This material is probably combustible.

Accidental Release Measures

Small spills/leaks

Should a spill occur while you are handling this chemical, FIRST REMOVE ALL SOURCES OF IGNITION, then you should dampen the solid spill material with 60-70% ethanol and transfer the dampened material to a suitable container. Use absorbent paper dampened with 60-70% ethanol to pick up any remaining material. Seal the absorbent paper, and any of your clothes, which may be contaminated, in a vapor-tight plastic bag for eventual disposal. Solvent wash all contaminated surfaces with 60-70% ethanol followed by washing with a soap and water solution. Do not reenter the contaminated area until the Safety Officer (or other responsible person) has verified that the area has been properly cleaned.

Stability and Reactivity

Stability

No data.

Incompatibilities

Organic amides/imides react with azo and diazo compounds to generate toxic gases Flammable gases are formed by the reaction of organic amides/imides with strong reducing agents Can react as acids.

Hazards Identification

EC Risk Phrase

R 40

EC Safety Phrase

S 22 36/37