Product Identification

Product Name

2-Chlorostyrene

Synonyms

1-Chloro-2-ethenylbenzene
2-Chlorostyrene

CAS

2039-87-4

Formula

C8H7Cl

Molecular Weight

138.6

EINECS

218-026-8

RTECS

WL4160000

RTECS Class

Other

Beilstein/Gmelin

2038863

Beilstein Reference

4-05-00-01345

Physical and Chemical Properties

Appearance

Clear yellow liquid.

Solubility in water

Insoluble

Melting Point

-63.2

Boiling Point

188.7

Vapor Pressure

1

Density

1.10001 g/cm3 (20 C)

Partition Coefficient

3.58

Usage

O-chlorostyrene is used in the manufacture of polychlorostyrene which is a clear, colorless plastic with good foaming, heat distortion and flame-retardant properties.

Vapor Density

4.7

Refractive Index

1.56487 (20 C)

First Aid Measures

Ingestion

Never give anything by mouth to an unconscious person. Get medical aid. Do NOT induce vomiting. If conscious and alert, rinse mouth and drink 2-4 cupfuls of milk or water.

Inhalation

Remove from exposure to fresh air immediately. If breathing is difficult, give oxygen. Get medical aid. DO NOT use mouth-to-mouth respiration. If breathing has ceased apply artificial respiration using oxygen and a suitable mechanical device such as a bag and a mask.

Skin

Get medical aid. Flush skin with plenty of soap and water for at least 15 minutes while removing contaminated clothing and shoes. Wash clothing before reuse.

Eyes

Flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower eyelids. Get medical aid.

Handling and Storage

Storage

Keep away from sources of ignition. Do not store in direct sunlight. Store in a tightly closed container. Flammables-area. Refrigerator (approx 4 C).

Handling

Wash thoroughly after handling. Use with adequate ventilation. Ground and bond containers when transferring material. Use spark-proof tools and explosion proof equipment. Avoid breathing dust, vapor, mist, or gas. Avoid contact with eyes, skin, and clothing. Empty containers retain product residue, (liquid and/or vapor), and can be dangerous. Keep container tightly closed. Avoid contact with heat, sparks and flame. Avoid ingestion and inhalation. Do not pressurize, cut, weld, braze, solder, drill, grind, or expose empty containers to heat, sparks or open flames.

Hazards Identification

Inhalation

May cause respiratory tract irritation. Aspiration may lead to pulmonary edema. Vapors may cause dizziness or suffocation. May cause cardiac abnormalities. Inhalation at high concentrations may cause CNS depression and asphixiation. May cause burning sensation in the chest.

Skin

May cause irritation and dermatitis. May cause cyanosis of the extremities.

Eyes

May cause eye irritation. May cause chemical conjunctivitis and corneal damage.

Ingestion

May cause gastrointestinal irritation with nausea, vomiting and diarrhea. May cause cardiac disturbances. Ingestion of large amounts may cause CNS depression.

Hazards

Vapors may form explosive mixtures with air. Vapors may travel to source of ignition and flash back. Most vapors are heavier than air. They will spread along ground and collect in low or confined areas (sewers, basements, tanks). Vapor explosion hazard indoors, outdoors or in sewers.

EC Risk Phrase

R 36/37/38

EC Safety Phrase

S 26 36

UN (DOT)

1993

Exposure Controls/Personal Protection

Personal Protection

Eyes: Wear appropriate protective eyeglasses or chemical safety goggles as described by OSHA's eye and face protection regulations in 29 CFR 1910.133 or European Standard EN166. Skin: Wear appropriate protective gloves to prevent skin exposure. Clothing: Wear appropriate protective clothing to prevent skin exposure.

Respirators

Follow the OSHA respirator regulations found in 29CFR 1910.134 or European Standard EN 149. Always use a NIOSH or European Standard EN 149 approved respirator when necessary.

Exposure Effects

Effects may be delayed.

Exposure limit(s)

NIOSH REL: TWA 50 ppm (285 mg/m3) ST 75 ppm (428 mg/m3)

Fire Fighting Measures

Flash Point

58

Fire Fighting

Wear a self-contained breathing apparatus in pressure-demand, MSHA/NIOSH (approved or equivalent), and full protective gear. During a fire, irritating and highly toxic gases may be generated by thermal decomposition or combustion. Will burn if involved in a fire. Use water spray to keep fire-exposed containers cool. Containers may explode in the heat of a fire. Extinguishing media: For small fires, use dry chemical, carbon dioxide, water spray or alcohol-resistant foam. For large fires, use water spray, fog, or alcohol-resistant foam. Use water spray to cool fire-exposed containers. Water may be ineffective. Do NOT use straight streams of water.

Fire Potential

This compound is combustible.

Accidental Release Measures

Small spills/leaks

Absorb spill with inert material, (e.g., dry sand or earth), then place into a chemical waste container. Avoid runoff into storm sewers and ditches which lead to waterways. Clean up spills immediately, using the appropriate protective equipment. Remove all sources of ignition. Use a spark-proof tool. Provide ventilation. A vapor suppressing foam may be used to reduce vapors.

Stability and Reactivity

Incompatibilities

Oxidizing agents, acids, bases, halogens.

Stability

Stable under normal temperatures and pressures. May discolor on exposure to light.

Decomposition

Hydrogen chloride, carbon monoxide, irritating and toxic fumes and gases, carbon dioxide.

Combustion Products

Fire may produce irritating, corrosive and/or toxic gases.

Transport Information

UN Number

1993

Hazard Class

3

Packing Group

I; II; III