Product Identification

Product Name

C.I. 11855

Synonyms

4'-(2-Hydroxy-5-methylphenylazo)acetanilide

CAS

2832-40-8

Formula

C15H15N3O2

Molecular Weight

269.3

EINECS

220-600-8

RTECS

AC3662000

RTECS Class

Tumorigen; Mutagen

Beilstein/Gmelin

753492

EC Index Number

611-055-00-0

EC Class

Carcinogenic Category 3; Sensitising

Physical and Chemical Properties

Appearance

Brownish-yellow powder.

Melting Point

268-270

Usage

For dyeing textiles, sheepskins & furs, for coloring polymethyl methacrylate & nylon.

First Aid Measures

Ingestion

DO NOT INDUCE VOMITING. If the victim is conscious and not convulsing, give 1 or 2 glasses of water to dilute the chemical and IMMEDIATELY call a hospital or poison control center. Be prepared to transport the victim to a hospital if advised by a physician. If the victim is convulsing or unconscious, do not give anything by mouth, ensure that the victim's airway is open and lay the victim on his/her side with the head lower than the body. DO NOT INDUCE VOMITING. IMMEDIATELY transport the victim to a hospital.

Inhalation

IMMEDIATELY leave the contaminated area; take deep breaths of fresh air. IMMEDIATELY call a physician and be prepared to transport the victim to a hospital even if no symptoms (such as wheezing, coughing, shortness of breath, or burning in the mouth, throat, or chest) develop. Provide proper respiratory protection to rescuers entering an unknown atmosphere. Whenever possible, Self-Contained Breathing Apparatus (SCBA) should be used.

Skin

IMMEDIATELY flood affected skin with water while removing and isolating all contaminated clothing. Gently wash all affected skin areas thoroughly with soap and water. If symptoms such as redness or irritation develop, IMMEDIATELY call a physician and be prepared to transport the victim to a hospital for treatment.

Eyes

First check the victim for contact lenses and remove if present. Flush victim's eyes with water or normal saline solution for 20 to 30 minutes while simultaneously calling a hospital or poison control center. Do not put any ointments, oils, or medication in the victim's eyes without specific instructions from a physician. IMMEDIATELY transport the victim after flushing eyes to a hospital even if no symptoms (such as redness or irritation) develop.

Handling and Storage

Storage

Keep in a cool, dry, dark location in a tightly sealed container or cylinder. Keep away from incompatible materials, ignition sources and untrained individuals. Secure and label area. Protect containers/cylinders from physical damage.

Handling

All chemicals should be considered hazardous. Avoid direct physical contact. Use appropriate, approved safety equipment. Untrained individuals should not handle this chemical or its container. Handling should occur in a chemical fume hood.

Hazards Identification

Ingestion

See inhalation.

Inhalation

Exposure to this compound may cause allergic, contact-type dermatitis. It may also cause irritation.

Skin

See inhalation.

Eyes

See inhalation

Exposure Controls/Personal Protection

Personal Protection

Chemical splash goggles in compliance with OSHA regulations are advised; however, OSHA regulations also permit other type safety glasses. Whre chemical resistant gloves. To prevent repeated or prolonged skin contact, wear impervious clothing and boots.

Respirators

Wear a NIOSH-approved half face respirator equipped with a combination filter cartridge, i.e. organic vapor/acid gas/HEPA (specific for organic vapors, HCl, acid gas, SO2 and a high efficiency particulate filter).

Fire Fighting Measures

Fire Fighting

Fires involving this material can be controlled with a dry chemical, carbon dioxide or Halon extinguisher.

Fire Potential

This material is probably combustible.

Accidental Release Measures

Small spills/leaks

Should a spill occur while you are handling this chemical, FIRST REMOVE ALL SOURCES OF IGNITION, then you should dampen the solid spill material with 60-70% ethanol and transfer the dampened material to a suitable container. Use absorbent paper dampened with 60-70% ethanol to pick up any remaining material. Seal the absorbent paper, and any of your clothes, which may be contaminated, in a vapor-tight plastic bag for eventual disposal. Solvent wash all contaminated surfaces with 60-70% ethanol followed by washing with a soap and water solution. Do not reenter the contaminated area until the Safety Officer (or other responsible person) has verified that the area has been properly cleaned.

Stability and Reactivity

Stability

No data.

Incompatibilities

Toxic gases are formed by mixing materials of this class with acids, aldehydes, amides, carbamates, cyanides, inorganic fluorides, halogenated organics, isocyanates, ketones, metals, nitrides, peroxides, phenols, epoxides, acyl halides, and strong oxidizing or reducing agents Flammable gases are formed by mixing materials in this group with alkali metals Explosive combination can occur with strong oxidizing agents, metal salts, peroxides, and sulfides Incompatible with strong oxidizing agents and strong acids.