1,1,2,2-Tetrafluoroethyl-2,2,3,3-tetrafluoropropylether Property

Boiling point:

92 °C

Density 

1.533

refractive index 

1.29

Flash point:

27.5 °C

storage temp. 

Sealed in dry,Room Temperature

form 

clear liquid

Specific Gravity

1.533

color 

Colorless to Almost colorless

InChI

InChI=1S/C5H4F8O/c6-2(7)4(10,11)1-14-5(12,13)3(8)9/h2-3H,1H2

InChIKey

HCBRSIIGBBDDCD-UHFFFAOYSA-N

SMILES

C(F)(F)C(F)(F)COC(F)(F)C(F)F

CAS DataBase Reference

16627-68-2(CAS DataBase Reference)

EPA Substance Registry System

(2H-Perfluoroethyl)(1H,1H,3H-perfluoropropyl)ether (16627-68-2)

Safety

Hazard Codes 

Xi

Risk Statements 

36/37/38

Safety Statements 

26-36

RIDADR 

3271

HazardClass 

IRRITANT

PackingGroup 

II

HS Code 

29091990

Hazard and Precautionary Statements (GHS)

Symbol(GHS)

Signal word

Warning

Hazard statements

H226Flammable liquid and vapour

Precautionary statements

P210Keep away from heat/sparks/open flames/hot surfaces. — No smoking.

P233Keep container tightly closed.

P240Ground/bond container and receiving equipment.

P241Use explosion-proof electrical/ventilating/lighting/…/equipment.

P242Use only non-sparking tools.

P243Take precautionary measures against static discharge.

P280Wear protective gloves/protective clothing/eye protection/face protection.

P303+P361+P353IF ON SKIN (or hair): Remove/Take off Immediately all contaminated clothing. Rinse SKIN with water/shower.

P370+P378In case of fire: Use … for extinction.

P403+P235Store in a well-ventilated place. Keep cool.

1,1,2,2-Tetrafluoroethyl-2,2,3,3-tetrafluoropropylether Chemical Properties,Usage,Production

Description

1,1,2,2-Tetrafluoroethyl-2,2,3,3-tetrafluoropropyl ether (HFE-458) is a hydrofluoroether. Hydrofluoroether is a new type of  chlorofluorocarbons (CFCs) substitute, ODP is zero, GWP is low, and the atmospheric residence time is very short. It is considered as one of the ideal substitutes for CFCs.

Uses

1,1,2,2-Tetrafluoroethyl-2,2,3,3-tetrafluoropropylether can be used as organic synthesis intermediates and pharmaceutical intermediates, mainly used in laboratory research and development processes and chemical production processes.

Synthesis

A system of a 6-L autoclave made of stainless steel was evacuated. The autoclave was charged with 401 g of potassium hydroxide (7.15 mol, 0.55 molar amount relative to 1 mol of a fluorine-containing alkyl alcohol), water (1604 mL), 2,2,3,3-tetrafluoro-1-propanol (boiling point of 109?? C., specific gravity of 1.4) represented by HCF2CF2CH2OH (1716 g, 13 mol) as a fluorine-containing alkyl alcohol. Then, the system was evacuated and replaced with nitrogen 20 times at room temperature. After evacuated, the system was filled with tetrafluoroethylene to 0.1 MPa, and the reaction system was heated to 85?? C. After the temperature in the system reached 85?? C., tetrafluoroethylene was added thereto little by little so that the reaction pressure was kept at 0.5 to 0.8 MPa. The temperature in the system was adjusted so as to be kept at 75 to 95?? C.Tetrafluoroethylene was added until the amount reached 0.5 molar relative to 1 mol of the fluorine-containing alkyl alcohol. The reaction was continuously carried out under stirring. When reduction in the pressure in the autoclave was stopped, the temperature in the autoclave was reduced to room temperature and unreacted tetrafluoroethylene was discharged, and the reaction was stopped. These steps took 5 hours to perform.The fluoroether of a lower phase of the production solution was HCF2CF2CH2OCF2CF2H (boiling point of 92?? C., specific gravity of 1.52). Table 1 shows the composition of the fluoroether production solution of a lower phase resulting from GC analysis.