4,4'-Methylenedianiline Property

Melting point:

89-91 °C(lit.)

Boiling point:

242 °C2 mm Hg(lit.)

Density 

1.15

vapor pressure 

0Pa at 25℃

refractive index 

1.5014 (estimate)

Flash point:

430 °F

solubility 

water: soluble

pka

5.32±0.25(Predicted)

color 

White to Light yellow

Water Solubility 

Slightly soluble. <0.1 g/100 mL at 19 ºC

Merck 

14,2980

BRN 

474706

Exposure limits

ACGIH: TWA 0.1 ppm (Skin)
OSHA: STEL 100 ppb

LogP

1.55 at 25℃

CAS DataBase Reference

101-77-9(CAS DataBase Reference)

NIST Chemistry Reference

Benzenamine, 4,4'-methylenebis-(101-77-9)

IARC

2B (Vol. 39, Sup 7) 1987

EPA Substance Registry System

4,4'-Methylenedianiline (101-77-9)

Safety

Hazard Codes 

T,N

Risk Statements 

45-39/23/24/25-43-48/20/21/22-51/53-68

Safety Statements 

53-45-61

RIDADR 

UN 2651 6.1/PG 3

WGK Germany 

3

RTECS 

BY5425000

TSCA 

Yes

HazardClass 

6.1

PackingGroup 

III

HS Code 

29215900

Hazardous Substances Data

101-77-9(Hazardous Substances Data)

Toxicity

LD50 oral in rabbit: 620mg/kg

Hazard and Precautionary Statements (GHS)

Symbol(GHS)

Signal word

Danger

Hazard statements

H301Toxic if swalloed

H317May cause an allergic skin reaction

H341Suspected of causing genetic defects

H350May cause cancer

H370Causes damage to organs

H373May cause damage to organs through prolonged or repeated exposure

H410Very toxic to aquatic life with long lasting effects

Precautionary statements

P202Do not handle until all safety precautions have been read and understood.

P260Do not breathe dust/fume/gas/mist/vapours/spray.

P273Avoid release to the environment.

P280Wear protective gloves/protective clothing/eye protection/face protection.

P301+P310IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician.

P302+P352IF ON SKIN: wash with plenty of soap and water.

4,4'-Methylenedianiline Chemical Properties,Usage,Production

Chemical Properties

4,4'-Methylenedianiline is a light brown crystalline solid with a faint amine odor. lt is very slightly soluble in water and soluble in alcohol, benzene,and ether. lt is combustible when exposed to heat or flame. When heated to decomposition，it emits toxic fumes of aniline and nitrogen oxides (NOx). The dihydrochloride is a crystalline solid that is soluble in water.

4,4'-Methylenedianiline is primarily used to produce 4,4-'methylenedianiline diisocyanate and other polymeric isocyanates which are used to manufacture polyurethane foams.

Uses

4,4'-Methylenedianiline is used in the production of polyurethane foams and epoxy resins. Potential contributor in pulmonary arterial hypertension (PAH) in rats through alteration of the serotenergic transport system. Drinking water contaminant candidate list 3 (CCL 3) compound as per United States Environmental Protection Agency (EPA), environmental, and food contaminants. Dyes and metabolites, Environmental Testing.

Preparation

93 g (1 mole) of aniline are dissolved in 96 % alcohol and to the cooled solution with proper stirring 120 g (1 mole) of 40 % formaldehyde solution are gradually added. After the addition is completed a second molecular portion of aniline, 93 g (1 mole) of aniline are added and the reaction is continued until the odor of formaldehyde has disappeared. The complete the reaction the mixture is refluxed for 2 hours. 130 g (1 mole) of aniline hydrochloride are then added, and boiling continued for a further 12 hours. The alcohol is distilled off, the residue made alkaline with the solution of sodium hydroxide and the excess of aniline removed by distillation with superheated steam. The residual oil, which consists of 4,4′-diaminodiphenylmethane, is then purified by solution in dilute hydrochloric acid and reprecipitation with dilute alkali. The 4,4′-diaminodiphenylmethane base is filtered off, washed and dried.

Organic medical chemicals, by M. Barrowliff, 188-189, 1921

Description

4,4'-Methylenedianiline is an industrial chemical that is not known to occur naturally. It is also commonly known as diaminodiphenylmethane or MDA. It occurs as a colorless to pale yellow solid and has a faint odor. 4,4'-Methylenedianiline is used mainly for making polyurethane foams, which have a variety of uses, such as insulating materials in mailing containers. It is also used for making coating materials, glues, Spandex? fiber, dyes, and rubber. 4,4'-Methylenedianiline is also a by-product of azo dyes. It is also possibly formed by hydrolysis of diphenylmethane-4A'-diisocyanate.

Chemical Properties

4,4-Diaminodiphenylmethane is a pale yellow crystalline solid (turns light brown on contact with air) with a faint amine-like odor that is unstable in the presence of light or air and emits toxic fumes of aniline and nitrogen oxides when heated to decomposition. 4,4'-Methylenedianiline is primarily used in industry as a chemical intermediate in the production of 4,4-methylenedianiline diisocyanates and polyisocyanates, but is also used as a cross-linking agent for the determination of tungsten and sulfates, and as a corrosion inhibitor. Exposure to this substance irritates the skin and eyes and causes liver damage. 4,4'-Methylenedianiline is reasonably anticipated to be a human carcinogen. (NCI05)

Uses

4,4'-methylenedianiline be used as organic intermediates. Mainly used for the synthesis of polyimide and as curing agent of epoxy resin.

Uses

4,4'-Diaminodiphenyl-methane is used in the determination of tungsten and sulfates; in the preparation of azo dyes; cross-linking agent for epoxy resins; in the preparation of isocyanates and polyisocyanates; in the rubber industry as a curative for neoprene, as an anti-frosting agent (antioxidant) in footwear; raw material in preparation of poly(amide-imide) resins (used in magnet-wire enamels); curing agent for epoxy res ins and urethane elastomers; corrosion inhibitor; rubber additive (accelerator, antidegradant, retarder) in tires and heavy rubber products; in adhesives and glues, laminates, paints and inks, PVC products, handbags, eyeglass frames, plastic jewelry, electric encapsulators, surface coatings, spandex clothing, hairnets, eyelash curlers, earphones, balls, shoe soles, face masks.

Uses

As chemical intermediate in production of isocyanates and polyisocyantes for preparation of polyurethane foams, Spandex fibers; as curing agent for epoxy resins and urethane elastomers; in production of polyamides; in the determination of tungsten and sulfates; in preparation of azo dyes; as corrosion inhibitor.

Definition

ChEBI: 4,4'-Methylenedianiline is an aromatic amine that is diphenylmethane substituted at the 4-position of each benzene ring by an amino group. It is primarily used in industry as a chemical intermediate in the production of 4,4-methylenedianiline diisocyanates and polyisocyanates.?

General Description

A tan flake or lump solid with a faint fishlike odor. May be toxic by inhalation or ingestion, and may be irritating to skin. Insoluble in water.

Air & Water Reactions

Oxidizes slowly in air in a reaction catalyzed by light. Somewhat hygroscopic. Insoluble in water.

Reactivity Profile

4,4'-Methylenedianiline polymerizes if heated above 257° F. Incompatible with strong oxidizing agents. 4,4'-Methylenedianiline is also incompatible with acids. Catalyzes isocyanate-alcohol and epoxide reactions. Flammable gaseous hydrogen may be generated in combination with strong reducing agents, such as hydrides.

Health Hazard

TOXIC; inhalation, ingestion or skin contact with material may cause severe injury or death. Contact with molten substance may cause severe burns to skin and eyes. Avoid any skin contact. Effects of contact or inhalation may be delayed. Fire may produce irritating, corrosive and/or toxic gases. Runoff from fire control or dilution water may be corrosive and/or toxic and cause pollution.

Fire Hazard

Combustible material: may burn but does not ignite readily. When heated, vapors may form explosive mixtures with air: indoors, outdoors and sewers explosion hazards. Contact with metals may evolve flammable hydrogen gas. Containers may explode when heated. Runoff may pollute waterways. Substance may be transported in a molten form.

Flammability and Explosibility

Non flammable

Safety Profile

Confirmed carcinogen with experimental tumorigenic data. Human poison by ingestion. Poison by subcutaneous and intraperitoneal routes. Human systemic effects by ingestion: rigidity, jaundice, other liver changes. An eye irritant. Mutation data reported. It is not rapidly absorbed through the skin. Combustible when exposed to heat or flame. When heated to decomposition it emits highly toxic fumes of aniline and NOx.

Potential Exposure

Used as an intermediate and as a curing agent. Approximately 99% of the DDM produced is con- sumed in its crude form (occasionally containing not more than 50% DDM and ply-DDM) at its production site by reac- tion with phosgene in the preparation of isocyanates and poly- isocyanates. These isocyanates and polyisocyanates are employed in the manufacture of rigid polyurethane foams which find application as thermal insulation. Polyisocyanates are also used in the preparation of the semiflexible polyure- thane foams used for automotive safety cushioning. DDM is also used as: an epoxy hardening agent; a raw material in the production of polyurethane elastomers; in the rubber industry as a curative for Neoprene and as an antifrosting agent (anti- oxidant) in footwear; a raw material in the production of Quana nylon; and a raw material in the preparation of poly (amide-imide) resins (used in magnet wire enamels).

First aid

If this chemical gets into the eyes, remove anycontact lenses at once and irrigate immediately for at least15 min, occasionally lifting upper and lower lids. Seekmedical attention immediately. If this chemical contactsthe skin, remove contaminated clothing and wash immediately with soap and water. Seek medical attention immediately. If this chemical has been inhaled, remove fromexposure, begin rescue breathing (using universal precautions, including resuscitation mask) if breathing hasstopped and CPR if heart action has stopped. Transferpromptly to a medical facility. When this chemical hasbeen swallowed, get medical attention. Give large quantities of water and induce vomiting. Do not make an unconscious person vomit.

Carcinogenicity

4,4′-Methylenedianiline and its dihydrochloride salt are reasonably anticipated to be human carcinogens based on sufficient evidence of carcinogenicity from studies in experimental animals.

Environmental Fate

MDA is a pale brown crystalline powder with a faint aminelike odor. Exposure to air and light results in polymerization and oxidation of MDA. When heated, MDA produces toxic fumes of aniline and nitrogen oxides.
Most MDA enters the environment when it is produced or used to make other compounds. Forty-five percent of the produced compound is released to deep soil, 52.6% to the air, and 2.4% to land and water. Once in the environment, it will be mainly present as tiny particles in the air and it is removed from the atmosphere by dry deposition, rain, and snow scavenging. A small amount is transformed by reaction with hydroxyl radicals. In water, most of MDA will attach to particles and sediments, and will eventually settle to the bottom.
The estimated half-life of biodegradation in surface water, groundwater, and soil is 1–7 days, 2–14 days, and 1–7 days, respectively. With respect to aquatic ecosystems, bioconcentration factor values of 3.0–14 suggest that bioconcentration is low, in addition this compound does not tend to build up in the food chain. When released to soil, it is expected to have slight to no mobility. Similarly, volatilization from both moist and dry soil surfaces is not expected to be important.

storage

Color Code—Blue: Health Hazard/Poison: Storein a secure poison location. Prior to working with thischemical you should be trained on its proper handling andstorage. Store in tightly closed containers in a cool, wellventilated area away from strong oxidizers (such as chlorine, bromine, and fluorine). A regulated, marked areashould be established where this chemical is handled, used,or stored in compliance with OSHA Standard 1910.1045.

Shipping

UN2651 4,40 -Diaminodiphenyl methane, Hazard Class: 6.1; Labels: 6.1-Poisonous materials.

Purification Methods

Crystallise the amine from water, 95% EtOH or *benzene. [Beilstein 13 IV 390.]

Toxicity evaluation

Currently, the mechanism of action is not completely understood and has been mostly assessed from information on structurally similar compounds. Many of the toxic properties of MDA have been attributed to metabolic intermediates, as these compounds are metabolically activated by N-oxidation to metabolites, such as N-hydroxymethylenedianiline, that react with DNA, RNA, and proteins.
Different studies suggest that both liver and thyroid are targets for MDA toxicity in humans and animals. Liver toxicity has been linked to impair mitochondrial function and structure, apoptosis, and increased oxidative stress. It may be caused by a reactive electrophile formed during metabolism since liver has the enzymatic routes necessary for such activation. Experimental studies indicate that biliary epithelial cells are damaged earlier than parenchymal cells and bile is a major route of exposure to MDA. The mechanism of thyroid toxicity has not yet been resolved. It has been observed that MDA exposure can induce a slight decrease in thyroid hormones in rats, thus triggering secretion of thyroid-stimulating hormone (TSH), which induced thyroid hyperplasia. Some of the induced adverse effects observed after MDA exposure (e.g., reduced food consumption, lower body weight gain, and effects on red cells, lymphocytes, and clotting parameters) could be explained as secondary responses.
MDA is carcinogenic to animals. The mechanism of liver or thyroid tumor development remains unclear. Even if cell injury may give indications of a nongenotoxic mechanism, it remains still unproved, and there are also positive genotoxic data in vitro and in vivo which indicate that a genotoxic mechanism may be related to the formation of a reactive metabolic intermediate cannot be excluded. Regarding thyroid cancer, hypersecretion of TSH may have a contribution to tumor formation.

Incompatibilities

Dust forms and explosive mixture with air. May polymerize in temperatures .125℃ . A weak base. Incompatible with strong oxidizers (chlorates, nitrates, peroxides, permanganates, perchlorates, chlorine, bromine, fluorine, etc.); contact may cause fires or explosions. Keep away from alkaline materials, strong acids. Flammable gas- eous hydrogen may be generated in combination with strong reducing agents, such as hydrides .

Waste Disposal

Controlled incineration (oxides of nitrogen are removed from the effluent gas by scrubbers and/or thermal devices).